收藏本站
CAT28F512
Erase-Verify Mode
The Erase-verify operation is performed on every byte
after each erase pulse to verify that the bits have been
erased.
Programming Mode
The programming operation is initiated using the pro-
gramming algorithm of Figure 7. During the first write
cycle, the command 40H is written into the command
register. During the second write cycle, the address of
the memory location to be programmed is latched on the
falling edge of WE, while the data is latched on the rising
edge of WE. The program operation terminates with the
next rising edge of WE. An integrated stop timer allows
for automatic timing control over this operation, eliminat-
ing the need for a maximum program timing specifica-
tion. Refer to AC Characteristics (Program/Erase) for
specific timing parameters.
Figure 6. A.C. Timing for Programming Operation
Program-Verify Mode
A Program-verify cycle is performed to ensure that all
bits have been correctly programmed following each
byte programming operation. The specific address is
already latched from the write cycle just completed, and
stays latched until the verify is completed. The Program-
verify operation is initiated by writing C0H into the
command register. An internal reference generates the
necessary high voltages so that the user does not need
to modify V CC . Refer to AC Characteristics (Program/
Erase) for specific timing parameters.
VCC POWER-UP SETUP PROGRAM LATCH ADDRESS
& STANDBY COMMAND & DATA
PROGRAM
VERIFY
PROGRAM
VERIFICATION
VCC POWER-DOWN/
STANDBY
PROGRAMMING COMMAND
ADDRESSES
CE (E)
tWC
tAS
tAH
tWC
tRC
tCS
tCH
tCH
tCS
tCH
tEHQZ
OE (G)
tGHWL
tWPH
tWHWH1
tWHGL
tDF
WE (W)
tDS
tWP
tDH
tDS
tWP
tDH
tWP
tDS
tDH
tOE
tOLZ
tOH
DATA (I/O)
HIGH-Z
DATA IN
= 40H
DATA IN
DATA IN
= C0H
tLZ
tCE
VALID
DATA OUT
VCC
5.0V
0V
tVPEL
VPP
VPPH
VPPL
? 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
11
Doc. No. MD-1084, Rev. K
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT28LV256GI-25T IC EEPROM 256KBIT 250NS 32PLCC
CAT28LV64WI-25T IC EEPROM 64KBIT 250NS 28SOIC
CAT28LV65WI25 IC EEPROM 64KBIT 250NS 28SOIC
CAT310W-T1 IC LED DVR 10CH AUTO 20SOIC
CAT32TDI-T3 IC LED DRVR WHITE BCKLGT TSOT-6
CAT3604VHV4-GT2 IC LED DVR WHT CLR BACKLT 16TQFN
CAT3606HV4-T2 IC LED DRVR WHITE BCKLGT 16-TQFN
CAT3614HV2-T2 IC LED DRVR WHITE BCKLGT 12-TDFN
相关代理商/技术参数
CAT28F512LA-12 功能描述:闪存 64 X 8 512K 120ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512LE12 制造商:ON Semiconductor 功能描述:
CAT28F512LI12 功能描述:闪存 64 X 8 512K 120ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512LI-12 制造商:ON Semiconductor 功能描述:Flash Parallel 5V 512Kbit 64K x 8bit 120ns 32-Pin PDIP Rail 制造商:ON Semiconductor 功能描述:Flash Memory IC
CAT28F512LI-15 制造商:Rochester Electronics LLC 功能描述:
CAT28F512LI90 功能描述:闪存 64 X 8 512K 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512N-12 功能描述:闪存 64 X 8 512K RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512N-12T 制造商:ON Semiconductor 功能描述:Flash Parallel 5V 512Kbit 64K x 8bit 120ns 32-Pin PLCC T/R